20 Inch Grass Steel Lawn Mover

20 inch grass steel lawn mover clutch handle of the cutting system is mounted on the other side of the handlebar. Also, a metal pull wire is connected to the lower side of the clutch handle, and the of mover is connected to the pinch wheel described above. Similarly, when the clutch handle is at In the front position, the cable is tightened, the pressure roller is close to the belt, and the power is connected, and the power is transmitted to the header portion through the belt; when the clutch handle is in the rear position, the cable is loose, the pressure pulley releases the power belt, and the power is broken. On, so this clutch handle can directly control the operation and stop of the header.

Send InquiryChat Now
Product Details

Technical Parameters

Cutting height: 25--75mm  

Rated speed: 2.9kw / 2800rpm  

Maximum power: 3.8kw / 3900rpm 

Cutting width: 508mm  

Capacity: 60L  

Wheel Size: 8 "/ 10"  

Chassis material: steel  

Carton size: 865 * 575 * 530  

Noise level: 96db  

Walking: hand push

Product operation system

 20 inch grass steel lawn mover clutch handle of the cutting system is mounted on the other side of the handlebar. Also, a metal pull wire is connected to the lower side of the clutch handle, and the of mover is connected to the pinch wheel described above. Similarly, when the clutch handle is at In the front position, the cable is tightened, the pressure roller is close to the belt, and the power is connected, and the power is transmitted to the header portion through the belt; when the clutch handle is in the rear position, the cable is loose, the pressure pulley releases the power belt, and the power is broken. On, so this clutch handle can directly control the operation and stop of the header.

 it has three position areas, which are front, middle and rear, respectively corresponding to the three areas on the throttle. In the final position, the throttle is closed. When the control handle is placed in the middle position, the throttle is moderate. Generally, when the engine is started, the handle is placed in the middle position. When the handle is pushed forward, the throttle is gradually increased. The larger the throttle, the stronger the engine's output power, and the throttle handle position can be adjusted at any time during walking and harvesting to obtain the required power.

Product show

1-1G122145953Y2.jpg

Product working  principle

comb-tooth rotating bevel gear increasing speed transmission mechanism and comb-tooth profile-type deepening device group; front and rear axles driving the bevel gear speed increasing transmission mechanism directly supported by the bearing block on the two sides of the frame The axial center line of the comb teeth is located directly above the longitudinal direction of the big double seedling eye or the small single seedling eye, each of which can be configured with 6 to 10 sets; the left and right single wing weeding shovel and comb teeth are correspondingly arranged on the front beam; The structure of the weeding machine is 8 to 10 times more efficient than the artificial alfalfa, the injury rate is low, and the cleaning rate of the seedlings is generally.

 

The foam filter is cleaned every 25 hours and the dust should be more frequent.

 

The foam filter is cleaned with kerosene or washing liquid and water, squeezed and dried.

 

The paper filter is cleaned every 25 hours and is more frequent when dust is large.

 

The filter is cleaned every 25 hours with a front air filter and the core is cleaned every 100 hours. It should be more frequent when dust is large. The front air filter is cleaned in the same way as the foam filter. The paper filter should be tapped on a flat surface.

About our service

Before-sale services:

1, 24 Hours online service, quickly reply for E-mail and online ask. Guide customers to choose the best applicable machine type.

2, professionally and patiently introduction, provide the advanced, energy-saving and practical technological process.

 

Sale services:

1, complete parts safety stock for all machine series. Test every machine before delivery to insure good performance of machine.

2, In accordance with the agreements stipulated in the contract.

 

After-sale services:

1,According to the special requirements of customers,Our company will send professional engineers to guide with device installation,

 Debugging and training operators until customers are fully satisfied.

2.The quality guarantee period for machines is one year except the wearing parts and human damage factor. 

 

 

Hot Tags: 20 inch grass steel lawn mover, China, suppliers, manufacturers, factory, wholesale, buy, price, quotation, in stock, made in China
Inquiry